-40%

NEW Internal Replacement Battery for Regular Edition Zip Zaps RC READ

$ 1.89

Availability: 301 in stock
  • Country/Region of Manufacture: China
  • Brand: ZipZaps
  • All returns accepted: ReturnsNotAccepted
  • Model: Regular Edition
  • Compatible Fuel Type: Electric
  • Compatible Brand: For ZipZaps
  • MPN: zzRE
  • Compatible Scale: 1:64
  • Condition: New

    Description

    NEW Internal Replacement Battery for Regular Edition Zip Zaps RC
    This listing is for an internal Battery for the Regular Edition RC Zip Zaps by Radio Shack
    Includes:
    Item as shown in pic. 1.
    Description:
    If your Regular Edition Zip Zap no longer charges or syncs with the controller. Your problem may be that the internal battery is corroded and does not charge.
    With a new internal battery it could be as good as new. Batteries were manufactured specifically for us and come pre-charged. The cell is 1.2 volts (nominal).
    --------------------------------READ----------------------------------------
    Pic. 2 (not included) shows what the interior of your Zip Zap should look like to be compatible with this battery - ie please don't confuse it with the Special Edition Zip Zaps.
    NO RETURNS WILL BE ACCEPTED IF YOU BUY THIS BATTERY FOR THE WRONG MODEL, RETURNS WILL ONLY BE ACCEPTED IF THERE IS A FAULT WITH THE BATTERY
    -------------------------------------------------------------------------------
    We also have the replacement batteries for the Special Edition - see:
    https://www.ebay.com/itm/NEW-Internal-Battery-for-Special-Edition-Zip-Zaps-Micro-RC-replacement-7AAAHR2A/124459754496?hash=item1cfa612400:g:0U0AAOSwWplfszPZ
    .
    The battery for the SE (Special Edition is slightly longer and rated at 2.4 V (nominal) and has part number "7AAAHR2A"
    Installation Step by Step Instructions:
    To install the batteries, remove the Zip Zap's car body.
    0) Recommended (but optional - you will have an unobstructed view of the clips)
    Remove the rear paired tires by pushing down & remove the motor with a small flat screwdriver.
    1) Using a small flat screwdriver (about the size used for eyeglass repair)
    Insert it vertically so that it's between the black body plastic and the clear plastic of the PCB cover.
    Carefully bend outward the BLACK chassis plastic tabs so the clear plastic cover's tabs holding the PCB can be moved up pass the black clips. (Black tab clips closest to the rear wheels)
    (NOTE: bend the black plastic because it is more flexable than the clear plastic - if you break the clear plastic tabs, just hot glue or 5 minute epoxy or tape the PCB clear cover back in place)
    2a) Now that the clear plastic tabs have been moved past the black plastic , you can PIVOT the PCB up to get at the old battery.
    2b) If it makes it easier you can slide the antenna wire (red for 49mhz, yellow for 27Mhz) past the plastic slot to make the printed circuit board easier to move out of the way
    3) Now that you have access to the battery you can remove the old battery with ideally non conductive plastic tweezers.
    Be careful not to nick or break the very thin enamel wires for the steering. Make sure you note which end (with the RED wire) has the +ve ridge when you remove it. If you are using metal tweezers make sure you do NOT touch the circuit board with the tweezers.
    IMPORTANT
    4a) If you notice a white/green oxide build up on the flat steel spring contacts (either +ve and/or -ve flat springs). You can use EMERY BOARDS to remove the oxide.
    4b) On the same flat steel springs use a SOFT ERASER to clean any oxide that might not be visable to the naked eye.
    4c) If you have it use 91-99% ISOPROPYL ALCOHOL to clean the same contacts.
    5a) To increase the pressure on the battery contacts, bend the flat springs. The easiest way I have found to do this is to insert a small screwdriver between the flat spring and the chassis at the mid point and use a 2nd screwdriver and at the top of the spring push it towards the chassis.
    5b) If done properly the flat spring should almost have a "U" or "V" shape.
    6a) If you have some use DIELECTRIC (PROTECTIVE) GREASE on the battery and the flat springs, to retard oxidation.
    6b) Insert the new replacement battery - BUT remember that the side of the battery with the RIDGE is positive and goes to the side of the flat spring with the RED wire connected. The negative side of the battery goes to the flat spring with the BLACK wire.
    7a/b) If this is a new car kit or one that has not been used for some time you may also need to use EMERY BOARDS and/or eraser on the contacts where the controller charges the car chassis.
    NOTE: This listing is for the battery ONLY, if you require the :
    EMERY BOARDS
    SOFT ERASER
    ISOPROPYL ALCOHOL SWAB
    PROTECTIVE (DIELECTRIC) GREASE
    these are included with the battery here in this listing:
    https://www.ebay.com/itm/124539217150
    This item is also for sale at our retail location and may be removed at any time.
    W A R R A N T Y
    Returns are accepted for faulty batteries. This item is sold with a 30 day repair or replace warranty. Returns are NOT accepted if the problem is with YOUR car, ie make sure the problem is with the batteries. Nor are returns accepted when buyers buy the battery for the wrong model of Zip Zap. Make sure you KNOW what model of Zip Zap you have.
    T E S T I M O N I A L S
    Check our feedback and bid with confidence. What our customers have said about this and similar items ;
    Excellent condition! As described! Would buy from again!
    PERFECT! And SUPER fast shipping! Thanks a lot! Highly Recommended! A+++++++++++
    Excellent, exactly as described - thanks!
    awesome deal AAAAAAAAAAAAAAAAAAAAAAA+++++++++++++++++++++++
    Immediate Paypal payment is required for Buy It Now items. For auction items payment should be received in 5 business days.
    U S A
    Handling time for US shipments is 2-3 business days.
    Shipping is by USPS or FedEX -  Addresses in the US should receive the item in 5 - 10 business days.
    We ship only on Tuesdays and Thursdays for the USA.
    For Tuesday shipment we require items to be paid no later than 11 am EST on the preceding Monday.
    For Thursday shipments we require that items be paid no later than 11 am EST on the preceding Wednesday.
    C a n a d a
    Handling time for Canadian shipments is 1-2 business days.
    Shipping is by Canada Post - Addresses in Canada should receive the item in 2-10 business days.
    We ship Mondays, Wednesdays and Fridays for Canada.
    An Ebay seller since 2000
    Images sell!
    Get Supersized Images & Free Image Hosting
    Create your brand with Auctiva's
    Customizable Templates.
    Attention Sellers - Get Templates
    Image Hosting, Scheduling at Auctiva.com.
    Track Page Views With
    Auctiva's FREE Counter